PlanaOS-P industrial and storm water treatment plants
PlanaOS-P treatment facilities are designed to clean industrial wastewater from industrial sites of enterprises from suspended solids, oil products and other related contaminants. Capacity from 10 to 50 l/s and more.
Benefits and features of PlanaOS-P:
- Calculation of technology for specific waste streams
- Configuration and equipment for the project
- Rational layout of block equipment
- Compliance with all design codes
- Convenient maintenance and repair
- 100% redundancy of the main equipment
Treatment facilities are designed individually for a specific facility. PlanaOS-P is used at thermal power, petrochemical and processing enterprises. Execution in the building allows you to rationally place a full set of technological equipment.
* An example of a layout solution. The external storage tanks for raw effluent and the tank for clean/rinsing water are not shown conventionally.
The PlanaOS-P treatment plants have a wide technological and climatic range of applications. The design of structures and the composition of equipment are specified at the design stage in order to achieve optimal solutions in terms of technical and economic indicators.
| Execution | Combined, production building and external process tanks |
| Performance | 10…50 l/s and more |
| Number of lines | From 1 to 3 |
| Reception and averaging of effluents | External storage tanks |
| Mechanical cleaning | Sand catcher, screw grate |
| Basic technology | Reagent treatment, sedimentation, laminar separation, mechanical and sorption filtration |
| Disinfection of drains | UV disinfection |
| Disposal of treated effluents | Under residual pressure / pressure |
| Sludge dewatering | Plate filter press / screw-plate dehydrator |
| Reservation | 100% hot reserve for drive equipment |
| Automation | LSU based on a programmable logic controller |
| Operator’s workplace | SCADA, mnemonic interface |
| KIP interfaces | 4…20 mA, HART |
| Interfaces with the Customer’s automated control system | RS 485 / Modbus RTU / Ethernet / Modbus TCP |
| Technological control | On-line measurements of wastewater quality |
| Additional | Spare parts, reagents and consumables for the period of the NDP |
The stations provide wastewater treatment up to the indicators given in the table.
| Indicator, mg/dm3 | At the inlet to the balance tank, before settling, no more than *) | At the entrance to the treatment plant, no more than | At the outlet of the treatment plant, no more than |
| Suspended solids | 1000 | 150 | 3 |
| BODfull | 100 | 30 | 3 |
| Petroleum products | 50 **) | 15 | 0.05 |
*) The storage tank must be equipped with a sand trap, oil retention and settling sections.
**) An increase in the concentration of oil products entering the treatment plant may require the installation of an oil and oil trap in front of the treatment plant.
«PLANA Engineering Group» supplies treatment facilities in the following composition:
2. Prefabricated tanks for accumulation and averaging of untreated wastewater (optional), including:
— tank designs;
— the system of insulation and heating of tanks and pipelines;
— anti-corrosion protection system;
— pipe and cable strapping;
— technological equipment and instrumentation for installation in tanks.
1. PS or pumping equipment for supplying wastewater to WWTP (optional).
3. A set of structures of a production light-assembly building for installation at the place of application.
4. Complete equipment and life support systems of the building, including systems:
— power supply;
— heating;
— ITP (if provided by the project);
— ventilation;
— lighting;
— safety and sygnal systems;
— lifting equipment;
— equipment of auxiliary premises.
5. A set of technological and auxiliary equipment, including:
— technological capacities;
— technological downloads;
— pumping equipment;
— pumping and dosing equipment;
— equipment for mechanical wastewater treatment;
— blower and compressor equipment;
— agitators and aeration systems of technological tanks;
— equipment for disinfection of treated wastewater;
— equipment for drainage, disinfection and dewatering of sediment;
— equipment for preparation and dosing of reagents;
— piping, shut-off and shut-off and control valves;
— drive (automated) shut-off and control valves;
— internal and external stairs, service platforms, decking, fencing;
— cable products, including power, control and network cables;
— cable entries, cable-carrying products, terminal boxes and racks.
6. Complete automation and control system, including:
— switching equipment for electric drives;
— control and measuring devices (instrumentation) and installation elements to them;
— local and main control cabinets, power supply, network equipment;
— automated control system (ACS) based on PLC and operator touch panel;
— adapted ACS application software;
— interface modules for communication with the Customer’s automated control system;
— the system of uninterruptible power supply of the ACS.
7. Reagents, consumables and tools for NDT and commissioning.
8. Spare parts for the warranty period of operation.
9. Assembly and installation and technical and operational documentation.
10. Declarations/certificates of conformity of the manufacturer, sanitary and epidemiological conclusion.
Services provided by PLANА Engineering Group :
— development of design and technical and operational documentation;
— transportation to the installation site;
— installation supervision services;
— NDP services («cold start-up»);
— participation in acceptance tests for commissioning into pilot operation;
— staff training.
The cost is determined by us in relation to your project, facility and wastewater quality.
At your request, we will provide a technical passport, a technological solution, a dimensional solution, bindings and loads, a commercial offer for the supply and provision of services.
Examples of implementations and projects
